Tadano TT-800XXL1 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 267

background image

Safety

1

WA01-0041E

Safety

Most accidents that occur during machine operation
and maintenance are caused by failure to observe
basic safety rules and precautions. Before operating
your machine or performing maintenance, read and
become familiar with all the safety precautions and
recommendations given in this section.
Remember that failure to observe even a single
precaution could involve you and the people around
the machine in a serious accident.

Foreseeing potential dangers is vital for preventing
accidents. All personnel working with the machine,
including the supervisor, machine operator and oiler,
should be sensitive to potentially dangerous situations
and take the necessary measures to prevent
accidents.

Safety precautions and recommendations are outlined
in this section and are also included in the operation
and maintenance instructions given in subsequent
sections. Warning labels are also provided on the
machine.
The cautionary instructions in this manual are
identified as "DANGER", "WARNING", "CAUTION" or
"NOTICE". These terms are defined as follows:

[NOTICE]

[NOTICE] indicates an important operational or

maintenance procedure or condition, which, if not
strictly observed, can result in damage to machine
components or deteriorated machine performance.

It is virtually impossible to anticipate every situation
that might present a hazard. The safety precautions
given in this manual and on the machine labels are
not exhaustive.
It is important, therefore, to strictly follow the
instructions in this manual and be sensitive to
potential dangers in order to prevent bodily injury and
damage to the machine.

Remember that your most important duty is to ensure
the safety of you, your co-workers and any other
people in the area.

DANGER indicates an imminently hazardous

situation, which, if not avoided, will result in death
or serious injury.

DANGER

WARNING indicates a potentially hazardous

situation, which, if not avoided, could result in
death or serious injury.

WARNING

CAUTION indicates a potentially hazardous

situation, which, if not avoided, may result in
a minor or moderate injury.

CAUTION

«
1
2
3
4
...
»

Содержание TT-800XXL1












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TT-800XXL1

Бренд: THORLABS Страницы: 44

Бренд: Canta Страницы: 2

Бренд: Danelec Страницы: 67

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Yamaha Страницы: 178

Бренд: Yamaha Страницы: 15

Бренд: Harken Страницы: 4

INTRA PROPHYwiz 181 P

Бренд: KaVo Страницы: 22

Бренд: Festo Страницы: 40

Бренд: Neurotech Страницы: 24

Бренд: Eleiko Страницы: 24

Бренд: Horizon Fitness Страницы: 17

Бренд: Wiltron Страницы: 13

Бренд: Tormach Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды