STILLE 530-1700 Скачать руководство пользователя страница 74

Страница: 74 / 80

Stille imagiQ2

service manual Technical

Technic

Zero position

13. Lateral tilt,

Run tabletop from maximum left inclination to maximum right inclination

and back.
Make sure that the table stops both times it passes zero position.

OK NOK

14. Longitudinal tilt (Trendelenburg)

Run tabletop from maximum head down to maxi-

mum head up and back.
Make sure that the table stops both times it passes zero position.

OK NOK

Panning (

True Free Float™

)

15. Pan functions,

test run both axis. check that motion works effortlessly and smooth

(manoeuvre with on hand only).

OK NOK

16. Mounting,

Check the pan handle attachment to rail.

It should fit firmly to rail

OK NOK

17. Cable,

Check that spiral cable and connector is undamaged.

OK NOK

Hydraulic

General

18. Oil,

check that oil level is correct.

The table shall be parked, table top in 0-position and in top position, the sound from the
motor shall be smooth there shall be there should be no “gurgeling” sound, oil in middle of
the tank.

OK NOK

19. Hoses,

Check that hose array is correct positioned at column

and check for wear and leakage.

OK NOK

Leakage

20. Cylinders,

Check that cylinders don’t have any external oil leakage (a small quantity of

oil on the piston shaft is normal).

OK NOK

21. Connections,

Check that connections don’t have any external oil leakage.

OK NOK

Electronic

22. Cables,

cable array is correct positioned at column and check for wear.

OK NOK

23. Control unit,

check that all connectors are properly attached

OK NOK

24. Ground connections,

Check that all ground points and potential equalisation points are

connected and tightened.

OK NOK

25. Grounding continuity,

Measure grounding continuity between the grounding pin on

the AC-inlet and potential equalisation connectors, and the front base cover

OK NOK

Mechanics

26. Wheels,

Check that wheels move freely and aren’t damaged.

OK NOK

27. Guide wheel (option),

check that the guide wheel moves to it’s end positions and isn’t

damaged

OK NOK

28. Column cover,

Check that column cover moves freely and doesn’t have any damages.

OK NOK

Содержание 530-1700

















































































Результаты поиска

Содержание 530-1700

Отзывы:

STILLE 530-1700, Служебное и техническое руководство, Страница: 74 / 80

Результаты поиска

Содержание 530-1700

Отзывы: