STILLE 530-1700 Скачать руководство пользователя страница 23

Страница: 23 / 80

Stille imagiQ2

service manual Technical

Technic

To replace Inclinometer board

Warning take measure for ESD protection

If possible place the table in position for service according to instruction, or

try to elevate the table top to the highest position, lock the wheels.

Remove the table top and the top cover, the emergency cover and then the

protective plates under the cover.

Perform an electric LoTo according to the instruction to remove any stored

energy in the system.

Protect the electrical components against ESD.

The inclinometer board is mounted with 4 screws, remove the screws.

Carefully remove the connector, pull straight up, do not “wiggle” the con-

nector, you might break it.

Reinstall the card and connector and mount it, restore the power according

to the LoTo procedure. NOTE! do not overtighten the scews tighten only lightly.

Test the functions, take care as the device is not protected by the covers, risk

for personal injury or damage to the device.

9) To calibrate a new 0-position, place the table in horizontal position with the

table top slightly raised in the front about 1-2 degrees up, turn OFF the hand

control and press the 0- button on the main board for 1 second, tunr table on and

check 0 position, if needed redo the previous steps.

10)

Reinstall the protective covers.

11)

Complete the LoTo procedure.

Содержание 530-1700

















































































Результаты поиска

Содержание 530-1700

Отзывы:

STILLE 530-1700, Служебное и техническое руководство, Страница: 23 / 80

Результаты поиска

Содержание 530-1700

Отзывы: