STILLE 530-1700 Скачать руководство пользователя страница 15

Страница: 15 / 80

Stille imagiQ2

service manual Technical

Technic

LoTo procedure Stille imagiQ2

LoTo = ”Lock out Tag out, the procedure to make the device safe

by removing stored energy.

Important information

This instruction is intended to be a support instruction to meet the requirements from OSHA 29

CFR 1910.147(c)(4) Energy Control Procedure. For the safe operation of this product, the users

and service manual must be followed. If the users manual is unavailable contact your service

organization, distributor or Stille AB directly on www.stille.se.

Take care for personal protections, reccomendation to wear protective eyeweare, and golves

when working with hydraulic system.

LOTO procedure Stille imagiQ2

(OSHA 29 CFR 1910.147(c)(4) Energy Control Procedure)

This procedure meets the basic LOTO requirements established by OSHA. It is designed to

insure that each employee involved in servicing this equipment has exclusive control over the

equipment. It is the obligation of each employee to follow this procedure and understand that

failing to do so can cause serious injury or death.

Field Service Engineers are recommended to have complete a LOTO Authorized and initial

LOTO Verification training to execute Lockout/Tagout on this system.

All non-authorized (non- service engineers) individuals are considered “affected” individuals.

The requires LOTO is described in respective repair instruction, if there are no speciffic repair

instruction perform both hydraulic and electric LOTO

Each individual LOTO can be performed separately or together with the others if needed, depen-

ding on the required operation.

If hydraulic LOTO is going to be performed, always start with the hydraulic LOTO then perform

the electric LOTO.

Содержание 530-1700

















































































Результаты поиска

Содержание 530-1700

Отзывы:

STILLE 530-1700, Служебное и техническое руководство, Страница: 15 / 80

Результаты поиска

Содержание 530-1700

Отзывы: