background image

NAVIGAT 100

056373/D

Alert Handling

3-9

Active Muted Warning

Press 

MENU / MUTE 

to mute a pending 

(active) unacknowledged warning.

The audible alarm is muted for a lim-
ited period of time (default = 30 Sec).

The display continuous to show the 
heading data from the selected compass 
(GYRO respectively MAGN),

together with the 

 sign for muted 

active warning,
„WARNING“ followed by the number of 
current alerts, the alert ID of the respec-
tive warning and the corresponding 
warning message.

The arrow symbols (



) indicate that the 

Left (

) / Right (

keys are to 

be used for scrolling forward and back displaying the warning messages 
in the alert list.

After a limited period of time, the audible alarm will raise again.

Active Acknowledged Warning

Press 

ENTER / ACK

 to acknowledge a 

pending (active) warning.

The audible alarm is completely 
muted.

The display continuous to show the 
heading data from the selected compass 
(GYRO respectively MAGN),

together with the 

 sign for muted 

active warning,
„WARNING“ followed by the number of 
current alerts, the alert ID of the respec-
tive warning and the corresponding 
warning message indicated by arrow 
symbols (



).

For scrolling forward and back and displaying the warning messages in 
the alert list, use the 

Left (

) / Right (

keys.

356.4°

WARNING 2/2

GYRO1

ID:694
GYRO SIM. ACTIVE

CSU

356.4°

WARNING 2/2

GYRO1

ID:694
GYRO SIM ACTIVE

CSU

Содержание NAVIGAT 100





















































































































































































































Отзывы: