Sperry Marine NAVIGAT 100 Скачать руководство пользователя страница 153

Страница: 153 / 212

NAVIGAT 100

056373/D

Service Setup 106

7-33

Service Setup 106 – Parameters

SENSOR SIMULATOR

Note

A restart is always automatically executed when the SENSOR SIMULA-
TOR menu is quit in case at least one setting was altered.

SIMULATOR VALUES

Editing masks for simulation of heading and ROT values of the sensor
are provided.

HEADING VALUE

Value:

[0 - 360°]

Default value: „000.0“

ROT VALUE

Value:

[+/- 9999 °/ min]

Default value: „0055.0“

SIMULATOR MODES

A selection of sensor simulator modes is provided.

SIMULATOR OFF

Settings:

none

The simulator off function is activated / inactivated via check
box.

Default setting: „inactive“

CONSTANT ROT

Settings:

none

The constant ROT function is activated / inactivated via
check box.

Default setting: „inactive“

CONSTANT HEADING

Settings:

none

The constant heading function is activated / inactivated via
check box.

Default setting: „inactive“

Содержание NAVIGAT 100





















































































































































































































Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды

Sperry Marine NAVIGAT 100, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды