Sperry Marine NAVIGAT 100 Скачать руководство пользователя страница 49

Страница: 49 / 212

NAVIGAT 100

056373/D

Optional Functions

2-11

2.9 Optional Functions

The following functions are available if the system is equipped with the
respective external controls and configured accordingly.

Muting Alarms Remotely

On alarm, actuate the mute control at a remote device (e.g. a central
alarm panel). The audible alarm is muted.

Note

A remotely muted alarm remains in the pending (unacknowledged) state.
The alarm message is shown on the display until the alarm is acknowl-
edged at the NAVIGAT 100 or the cause of the alarm is eliminated.

Содержание NAVIGAT 100





















































































































































































































Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды

Sperry Marine NAVIGAT 100, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды