Sperry Marine NAVIGAT 100 Скачать руководство пользователя страница 172

Страница: 172 / 212

056373/D

NAVIGAT 100

9-10

NAVIGAT 100 Software Update

21. Continue the software update for the second software file 5026-1093-

096 (for CSU controller update via J32 service port) and

22. The “Online” button at the top of SUSI’s main screen should now

become clickable (not greyed-out):

23. Click

to connect to the device.

24. The following blank SUSI screen indicates at the status line, that

SUSI is connected with CSU.



The LED symbol at the top of the screen should have changed its col-
our to green:

plug in the type B connector of the
USB cable at the J32 USB service
port on the NAVIGAT 100 main-
board.

Содержание NAVIGAT 100





















































































































































































































Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды

Sperry Marine NAVIGAT 100, Руководство по эксплуатации, установке и обслуживанию

Результаты поиска

Содержание NAVIGAT 100

Отзывы:

Похожие инструкции для NAVIGAT 100

Бренды по названию

Популярные бренды