South Bend Tools SB1119 Скачать руководство пользователя страница 59

Страница: 59 / 76

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-57-

S E R V I C E

Figure

Figure 97. Location jam nuts on gib set screws.

. Location jam nuts on gib set screws.

Loosen (4) jam nuts on gib set screws (see

Figure 97).

Evenly adjust set screws in small amounts

then test results using methods in Steps

–

When you are satisfied with gib adjustment,

tighten jam nuts without turning set screws.

Repeat

Steps 2

–

3 to confirm gib adjustment.

If necessary, repeat Steps 5

–

Close cabinet door.

Squaring Spindle

To reduce the risk of kickback and to increase the

quality of cuts, it is important to make sure the

spindle and table are perpendicular, or "square",

to each other in all directions. This process will

require taking measurements at many different

positions.

To get a perpendicular alignment between

the table and spindle, it will be necessary to

take multiple readings and make multiple

adjustments to the adjusting hex bolt at each

corner of the spindle housing.

Figure

Figure 98. Illustration of using machinist's square to

. Illustration of using machinist's square to

square spindle to table.

Front of Table

Spindle

90°

Machinist’s

Square

Machinist’s

Square

Spindle

Figure

Figure 99. Illustration of machinist's square

. Illustration of machinist's square

measuring spindle squareness at different directions.

Tools Needed

Qty

Machinist's Square ................................................1

Open-End Wrench 30mm .....................................1

— If there are no gaps anywhere between

square and table or spindle, no

adjustment is necessary.

— If there is a gap anywhere between square

and table or spindle, proceed to Step 6.

To square spindle:

DISCONNECT MACHINE FROM POWER!

Remove guard/fence assembly from table.

Remove any cutters or spacers from spindle.

Use spindle height handwheel to raise

spindle to its highest position.

Position machinist's square against spindle

and table to check squareness (see Figures

–

99).

Содержание SB1119













































































Результаты поиска

Содержание SB1119

Отзывы:

South Bend Tools SB1119, Руководство пользователя, Страница: 59 / 76

Результаты поиска

Содержание SB1119

Отзывы: