manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 26 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 26

OPERATION

-24-

For Machines Mfd. Since 3/21

South Bend Tools

Model SB1119/SB1120

O P E R A T I O N

Operation Overview

To complete a typical operation, the operator 

does the following:

1. 

Examines the workpiece to make sure it is 

suitable for cutting.

2.  

Installs cutter onto spindle and adjusts 

spindle height for operation.

3. 

Correctly adjusts cutter guard and fence for 

operation and locks them in place.

4.  

Checks outfeed side of machine for proper 

support and to make sure workpiece can 

safely move past cutter without interference.

5.  

Places workpiece on infeed side of machine 

and stabilizes it with featherboards, jigs, or 

other safety workpiece holding devices.

6. 

Removes any clothing, apparel, or jewelry 

that may become entangled in shaper.

7.  

Ensures RPM adjustment knob is turned 

all the way counterclockwise and FOR/REV 

switch is in the OFF position.

8. 

Turns machine ON.

9.  

Verifies cutter rotation and feed directions.

10.  

Sets spindle speed for operation.

11.  

Feeds workpiece through cut while 

maintaining firm pressure on workpiece 

against both table and fence, while always 

keeping hands and fingers out of the cutting 

path.

12.  

Turns machine OFF.

To reduce the risk of 

serious injury when using 

this machine, read and 

understand this entire 

manual before beginning 

any operations.

The purpose of this overview is to provide 

the novice machine operator with a basic 

understanding of how the machine is used during 

operation, so they can more easily understand 

the controls discussed later in this manual.

Note:

 Due to the generic nature of this overview, 

it is not intended to be an instructional guide for 

performing actual machine operations. To learn 

more about specifi c operations and machining 

techniques, seek training from people experienced 

with this type of machine, and do additional 

research outside of this manual by reading "how-

to" books, trade magazines, or websites.

If you are not experienced with this type 

of machine, WE STRONGLY RECOMMEND 

that you seek additional training outside of 

this manual. Read books/magazines or get 

formal training before beginning any projects. 

Regardless of the content in this section, 

South Bend Tools will not be held liable for 

accidents caused by lack of training.

To reduce risk of short and 

long term injury, wear eye, 

ear, and lung protection 

when using this machine.

Keep hair, clothing, and jew-

elry away from moving parts 

at all times. Entanglement 

can result in death, ampu-

tation, or severe crushing 

injuries!

Содержание SB1119













































































Отзывы:

Нет отзывов