South Bend Tools SB1119 Скачать руководство пользователя страница 42

Страница: 42 / 76

-40-

For Machines Mfd. Since 3/21

South Bend Tools

Model SB1119/SB1120

A C C E S S O R I E S

Shop-Made Safety
Accessories

Shop-made safety accessories provide support

and various options for different operations.

These accessories can reduce the risk of kickback

and keep fingers and hands away from the cutter

rotation.

To make a zero-clearance fence:

DISCONNECT MACHINE FROM POWER!

Remove fence faces and mounting brackets

from guard/fence base by loosening fence

lock knobs (see Figure 60).

Making a Zero-Clearance Fence

Figure

Figure 60. Fence face removal components.

. Fence face removal components.

Fence

Lock Knob

(1 of 2)

Fence Mounting Bracket

(1 of 2)

Fence Face

(1 of 2)

A shop-made zero-clearance fence provides more

support than a standard fence and reduces

tearout on narrow or fragile stock. Using a zero-

clearance fence is the best way to reduce the risk

associated with shaping inherently dangerous

small stock.

Remove (2) cap screws shown in Figure 61

from each fence mounting bracket.

Figure

Figure 61. Fence mounting bracket cap screw

. Fence mounting bracket cap screw

location.

x 2

Select piece of straight and smooth stock

that is same height and thickness as fence

faces and approximately 30" long.

Position board over length of guard/fence

assembly and mark mounting holes and

outline cutter and spindle profile.

Cut an outline of spindle and cutter from

center of stock, as illustrated in Figure 62.

" or thicker

wood stock

Mount with

existing hardware

Drill two-step

holes

Cut out profile

of cutter & spindle

Figure

Figure 62. Example of a zero-clearance fence.

. Example of a zero-clearance fence.

Note:

Make outline as close as possible to

cutter and spindle without interfering with

rotation.

ACCESSORIES

Tool Needed

Qty

Hex Wrench 5mm .................................................1

Straight, Smooth Stock 30" ..................................1

Marker or Pencil ...................................................1

Straight, Smooth Stock 30" ..................................1

Wood Cutting Tool ................................................1

Drill & Drill Bits for Countersinking ...As Needed

Fence Mounting Hardware ...................As Needed

Содержание SB1119













































































Результаты поиска

Содержание SB1119

Отзывы:

South Bend Tools SB1119, Руководство пользователя, Страница: 42 / 76

Результаты поиска

Содержание SB1119

Отзывы: