manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 21 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 21

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-19-

P R E P A R A T I O N

Lifting & Moving

The Model SB1119/SB1120 can be lifted with one 

of the following methods:

•  Lifting Straps & Safety Hooks: Connect 

two safety hooks to chains or web straps that 

are capable of securely hooking underneath 

the table edge at the locations shown in 

Figure 15. Then attach the chains or web 

straps to a center safety chain secured to the 

power lifting equipment. 

•  Forklift Forks: Position the forks under the 

table and close to the cabinet (see Figure 

15). Use cardboard to protect the table and 

cabinet from the forks.

Figure 15. Lifting location example.

Figure 15. Lifting location example.

This machine and its 

parts are heavy! Serious 

personal injury may occur 

if safe moving methods are 

not used. To reduce the 

risk of a lifting or dropping 

injury, ask others for help 

and use power equipment.

Assembly

The machine must be fully assembled before it 

can be operated. Before beginning the assembly 

process, refer to Required for Setup on Page 

13 and gather all listed items. To ensure the 

assembly process goes smoothly, first clean any 

parts that are covered or coated in heavy-duty 

rust preventative (if applicable).

Assembly of the Model SB1119/SB1120 consists 

of checking the table insert flushness, assembling 

the spindle and drawbar, and leveling the 

machine

To assemble machine:

1.

  Remove (2) inner inserts from table opening 

(see Figure 16).

Incorrect assembly of spindle and drawbar 

can cause the spindle and cutter to fly off 

machine, causing injury or death. Make 

certain spindle is properly assembled before 

operating machine. If you are uncertain of any 

aspect of assembly, please review instructions 

again or contact customer service.

Figure 

Figure 16. Location of two inner inserts (front cutter 

. Location of two inner inserts (front cutter 

guard removed for clarity).

guard removed for clarity).

Inner Inserts

Inner Inserts

Outer Insert

Outer Insert

Содержание SB1119













































































Отзывы:

Нет отзывов