South Bend Tools SB1119 Скачать руководство пользователя страница 58

Страница: 58 / 76

-56-

For Machines Mfd. Since 3/21

South Bend Tools

Model SB1119/SB1120

S E R V I C E

Loosen (4) Phillips head screws enough to

remove motor access panel (see Figure 95).

Loosen (4) hex bolts securing motor mount to

bracket (see Figure 96). It may be easier to

access back bolts from cabinet door.

Figure

Figure 95. Location of motor access panel and

. Location of motor access panel and

securing screws.

Figure

Figure 96. Location of motor mounting bolts.

. Location of motor mounting bolts.

x 4

Using straightedge as guide, adjust height/

angle of motor until pulleys are aligned, then

re-tighten hex bolts.

Install motor access panel and tighten

screws loosened in Step 4.

x 4

Adjusting Spindle Gib

The gib controls the smoothness of the slide

movement, as well as the run-out or end play

of the spindle. Tightening the gib too much will

make it hard to adjust the height of the spindle

and cause excessive wear on the slide. Loosening

the gib too much will introduce spindle end play

and cause poor cutting results and excessive

wear on the spindle bearings.

Tools Needed

Qty

Open-End Wrench 30mm .....................................1

Hex Wrench 10mm ...............................................1

To adjust spindle gib:

DISCONNECT MACHINE FROM POWER!

Use spindle height handwheel to raise

spindle to its highest position.

— If it is difficult to turn handwheel or you

feel resistance from spindle slide, gib may

need to be loosened. Proceed to Step 4.

Attempt to wiggle top of spindle.

— If there is movement, proceed to Step 4.

— If there is no movement, no adjustment is

necessary.

Open cabinet door.

Motor

Access

Panel

Содержание SB1119













































































Результаты поиска

Содержание SB1119

Отзывы:

South Bend Tools SB1119, Руководство пользователя, Страница: 58 / 76

Результаты поиска

Содержание SB1119

Отзывы: