manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 56 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 56

-54-

For Machines Mfd. Since 3/21

South Bend Tools

Model SB1119/SB1120

S E R V I C E

— If there are no gaps anywhere between 

straightedge and fence faces, no 

adjustment is necessary.

— If there is a gap between straightedge and 

fence faces, proceed to Step 5.

5.

  With straightedge against fence faces, adjust 

fence set screws in small increments until 

any gaps are bridged (see Figure 91).

Figure 

Figure 91. Location of fence face set screws.

. Location of fence face set screws.

4.

  Place straightedge against both fence faces 

(see Figure 90).

Figure 

Figure 90. Example of aligning fence faces.

. Example of aligning fence faces.

!

x 8

Truing Wooden Fences

A flat and properly aligned fence creates a safer, 

smoother cutting operation. A damaged or worn 

fence should be replaced. If choosing to replace 

or use wooden boards as fence faces, follow the 

instructions below to ensure each is properly 

flattened and aligned correctly.

To true wooden fences:

1.

  Refer to Making a Zero-Clearance Fence 

on Page 40 for instructions on replacing 

aluminum fence faces with wood.

2.

  DISCONNECT MACHINE FROM POWER!

3.

  Ensure bolts through wood fence facing 

on each side are tight and adequately 

countersunk.

4.

 Follow 

Steps 2

–

3 of Aligning Fence Faces 

on Page 53.

5.

  Place straightedge against both fence faces 

(see Figure 92).

Figure 

Figure 92. Example of aligning fence faces.

. Example of aligning fence faces.

!

Items Needed 

Qty

Hex Wrench 5mm .................................................1

Straight, Smooth Stock 30" ..................................1

Marker or Pencil ...................................................1

Straight, Smooth Stock 30" ..................................1

Wood Cutting Tool ................................................1

Drill & Drill Bits for Countersinking ...As Needed

Fence Mounting Hardware ...................As Needed

Precision Straightedge 12" ...................................1

Jointer ....................................................................1

Содержание SB1119













































































Отзывы:

Нет отзывов