manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 15 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 15

PREPARATION

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-13-

P R E P A R A T I O N

Like all machinery there is potential danger 

when operating this machine. Accidents are 

frequently caused by lack of familiarity or 

failure to pay attention. Use this machine with 

respect and caution to decrease the risk of 

operator injury. If normal safety precautions 

are overlooked or ignored, serious personal 

injury may occur.

No list of safety guidelines can be complete. 

Every shop environment is different. Always 

consider safety first, as it applies to your 

individual working conditions. Use this and 

other machinery with caution and respect. 

Failure to do so may result in serious personal 

injury or property damage.

Preparation Overview Required for Setup

The purpose of the preparation section is to help 

you prepare your machine for operation. The list 

below outlines the basic process. Specific steps 

for each of these points will be covered in detail 

later in this section.

The typical preparation process is as follows:

1.

  Unpack the machine and inventory the 

contents of the box/crate.

2.

  Clean the machine and its components.

3.

  Identify an acceptable location for the 

machine and move it to that location.

4.

  Level the machine and either bolt it to the 

floor or place it on mounts.

5.

  Assemble the loose components and make 

any necessary adjustments or inspections to 

ensure the machine is ready for operation.

6.

  Connect the machine to the power source.

7.

  Test run the machine to make sure it 

functions properly and is ready for operation.

The items listed below are required to 

successfully set up and prepare this machine for 

operation.

For Lifting

•  A forklift or other power lifting device rated 

for the weight of the machine.

•  Lifting Straps or Chain (rated for at least 

1000 lbs.)

For Power Connection

•  A power source that meets the minimum 

circuit requirements for this machine. (Refer 

to the Power Supply Requirements 

section for details.)

•  A qualified electrician to ensure a safe and 

code-compliant connection to the power 

source.

For Assembly

•  Disposable Rags 

•  Cleaner/Degreaser 

•  Safety Glasses 

•  Disposable Gloves

•  Straightedge 12"

•  Socket or Wrench 

13

⁄

16

"

•  Precision Level

•  Dust Collection System

•  Dust Hose 4" 

•  Hose Clamp 4"

Содержание SB1119













































































Отзывы:

Нет отзывов