South Bend Tools SB1119 Скачать руководство пользователя страница 51

Страница: 51 / 76

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-49-

M A I N T E N A N C E

Items Needed

Qty

Mineral Spirits ......................................As Needed

Shop Rags ..............................................As Needed

Wire Brushes ........................................................2

NLGI#2 Grease .....................................As Needed

Elevation Leadscrew & Spindle
Slides

Lubrication Type ..........T26419 or NLGI#2 Equiv.

Amount ................................................... Thin Coat

Frequency .............................................. As Needed

Fence Rack & Pinion

Lubrication Type ..........T26419 or NLGI#2 Equiv.

Amount ................................................... Thin Coat

Frequency .............................................. As Needed

Adjust guard/fence base fully forward then push

the assembly forward off the front end of the

fence racks to fully reveal the racks (see Figure

78). Use a rag and mineral spirits to wipe off

any built-up grease and saw dust. Apply a thin

coat of lubricant to the racks using a wire brush

before replacing the guard/fence assembly.

Adjust the assembly forward and back to

distribute the grease.

Figure

Figure 77. Location of spindle slides and leadscrew.

. Location of spindle slides and leadscrew.

Slide

Leadscrew

Items Needed

Qty

Mineral Spirits ......................................As Needed

Shop Rags ..............................................As Needed

Wire Brushes ........................................................1

NLGI#2 Grease .....................................As Needed

Lower spindle housing assembly fully by

turning handwheel counterclockwise. Clean the

leadscrew threads and slides with a wire brush,

rag, and mineral spirits (see Figure 77). Brush

new grease on slides and leadscrew with a clean

wire brush and move the spindle assembly up

and down a few times to evenly distribute the

grease.

Racks

Figure

Figure 78. Location of fence racks.

. Location of fence racks.

Содержание SB1119













































































Результаты поиска

Содержание SB1119

Отзывы:

South Bend Tools SB1119, Руководство пользователя, Страница: 51 / 76

Результаты поиска

Содержание SB1119

Отзывы: