manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 45 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 45

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-43-

A C C E S S O R I E S

Making Box Guards

Shop-made box guards are an excellent way 

to enclose the cutter to virtually eliminate 

accidental contact with the cutter during 

operation. Having the cutter enclosed also helps 

increase the efficiency of dust collection. The 

drawback to box guards is that one size does 

not fit all. Often, professional woodworkers who 

use box guards make multiple guards that are 

different sizes.

Figure 66 shows one way to make and attach 

a box guard to the Model SB1119/SB1120. This 

guard replaces the vertical clear plastic guard 

that is included with the shaper. For durability 

and strength, use a hardwood when making box 

guards. When installing the box guard, adjust 

the box guard approximately 

1

⁄

4

" above the stock 

you will shape and use featherboards on both 

sides.

Note:

 DO NOT use the box guard as a hold-

down or featherboard; instead, use the provided 

featherboard that has the ability to flex with the 

minor height variations of your stock.

Tips for making a custom box guard:

The thickness of your workpiece will determine 

the height of the box guard. Therefore, you will 

need to build a separate box guard for each 

workpiece of a different thickness. A box guard 

can be used with or without a zero-clearance 

fence (see Making Zero-Clearance Fence on 

Page 40 for instructions).

The box guard can either attach directly to 

wooden fence boards (or board) with screws (as 

shown in Figure 67) or attach directly to the 

guard fence assembly with the plastic guard 

hardware (as shown in Figure 66). In either 

case, featherboards should also be used on either 

side to support the workpiece. Construct the box 

guard in a way that it extends out over the cutter 

area while leaving enough distance between the 

guard and the table for the workpiece to easily 

pass by the cutter. Refer to Figure 67 for an 

example.

1

2

3

Figure 

Figure 66. Box guard attached instead of included 

. Box guard attached instead of included 

clear plastic guard (fence and guard components 

clear plastic guard (fence and guard components 

removed for clarity).

removed for clarity).

Fence

Board

Box

Guard

Workpiece

Figure 

Figure 67. Example of custom box guard attached to 

. Example of custom box guard attached to 

wooden fence boards.

wooden fence boards.

Содержание SB1119













































































Отзывы:

Нет отзывов