manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 31 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 31

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-29-

O P E R A T I O N

7.

  Tighten cap screw with hex wrench while 

holding spindle stationary with spindle 

wrench (see Figure 37).

Figure 

Figure 37. Tightening spindle cap screw.

. Tightening spindle cap screw.

8.

  Lower spindle to desired height and adjust 

cutter guard for operation.

!

Using Push Sticks

When used correctly, push sticks reduce the 

risk of injury by keeping hands away from the 

cutter. In the event of an accident, a push stick 

can absorb damage that would have otherwise 

happened to hands or fingers. Use push sticks 

whenever your hands will get within 12" of the 

cutter. To make your own push sticks, refer to 

Making Push Sticks on Page 42. To maintain 

control when shaping large workpieces, start by 

feeding with your hands then use push sticks to 

finish the operation, so your hands are not on 

the end of the workpiece as it passes through the 

cutter.

Figure 

Figure 38. Side view of push stick in use.

. Side view of push stick in use.

Supporting: A second push stick can be used 

to keep the workpiece firmly against the fence 

while cutting (see Figure 39). When using 

this method, only apply pressure against the 

fence before the cutter; otherwise, pushing the 

workpiece against or behind the cutter will 

increase the risk of kickback (see "Supporting 

Push Stick Prohibition Zone" in Figure 39).

Feeding: Place the notched end of the push stick 

against the end of the workpiece (see Figure 

38), and move the workpiece into the cutter with 

steady downward and forward pressure.

Supporting

Push Stick

Prohibition

Zone

Push Stick

Push Stick

Supporting

Feeding

Figure 

Figure 39. Supporting with second push stick.

. Supporting with second push stick.

Содержание SB1119













































































Отзывы:

Нет отзывов