manualshive.com logo in svg

South Bend Tools SB1119, Руководство пользователя, Страница: 5 / 76

Поделиться
Скачать
South Bend Tools SB1119 Скачать руководство пользователя страница 5

South Bend Tools

For Machines Mfd. Since 3/21

Model SB1119/SB1120

-3-

I N T R O D U C T I O N

Description of Controls 
& Components

Refer to Figures 1–9 and the following 

descriptions to become familiar with the basic 

controls and components used to operate this 

machine.

Figure 

Figure 1. Control panel.

. Control panel.

A

A

H

H

G

G

F

F

B

B

C

C

D

D

E

E

JJ

Figure 

Figure 3. Cabinet components.

. Cabinet components.

K

K

J.  Miter Gauge: 

Supports workpiece for 

controlled straight or angled cuts as it slides 

along the work table miter slot. 

K.  Spindle Height Handwheel: 

Raises and 

lowers spindle and cutter to desired height.

Serious personal injury could occur if 

you connect the machine to power before 

completing the setup process. DO NOT 

connect power until instructed to do so later 

in this manual.

Untrained users have an increased risk 

of seriously injuring themselves with this 

machine. Do not operate this machine until 

you have understood this entire manual and 

received proper training.

A.  RPM Digital Readout Screen: 

Displays 

spindle RPM.

B.  RPM Adjustment Knob:

 Adjusts spindle 

speed between 5,000

–

10,000 RPM.

C.  STOP Button:

 Turns machine OFF and 

prevents it from starting.

D.  ON Button: 

Turns machine ON.

E.  Forward/Reverse (FOR/REV) Switch:

 

Starts, stops, and reverses spindle rotation.

F.  Unit (mm/in.) Button:

 Switches spindle 

height display to either inches or 

millimeters.

G.  Zeroing (0" Set) Button:

 Adjusts spindle/

cutter height to 0 in./mm.

H.  Spindle Height Digital Readout Screen: 

Displays spindle/cutter height in either 

inches or millimeters.

II

Figure 

Figure 2. Starting pin.

. Starting pin.

I.  Starting Pin: 

Supports workpiece during 

freehand cuts until it contacts rub collar 

(refer to Page 36).

Содержание SB1119













































































Отзывы:

Нет отзывов