Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 36

Страница: 36 / 64

Section 2

Pump Programming - Intermittent Delivery Mode

Intermittent Programming

Before programming:

Stop the pump and change the Lock Level to LL0 as described on

page 9.

Select the Intermittent (INTERMT) delivery mode as described in

Changing Delivery Modes on page 10. If the pump is already in the

INTERMT delivery mode, you may select it again to clear all

programming screens to their default settings.

1. Begin at the main screen

Make sure the pump is in LL0.

Make sure INT and STOPPED

appear on the main screen.

Press

„

to begin.

2. Enter the reservoir volume

Press

to select the volume

of fl uid in a fi lled reservoir. (If you

do not wish to use the Reservoir

Volume feature, scroll down to

“Not In Use” located before 1.)

Press

€

3. Enter the dose volume

Press

to select the

desired dose volume in milliliters.

Press

€

4. Enter the dose duration

Press

to select the

time period over which dose

will be delivered.

Press

€

Reservoir Volume

| 100.0 ml

<Range: 1 - 9999>

Dose Volume

| 50.0 ml

<Range: 0.1 - 1000>

*** INT 6240X ***

STOPPED

Press NEXT to advance

Dose Duration

| 1 hrs 00 min

<Range: 00:09-24:00>

IN19822.indd 30

10/24/2011 3:57:16 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды