Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 3

Страница: 3 / 64

This guide pertains only to the CADD-Prizm

VIP (Variable Infusion

Profile) Model 6100 and 6101 ambulatory infusion pump and the following

delivery modes:

PCA

Continuous

TPN

Intermittent

PCA 6210

CONTIN 6220

TPN 6230

INTERMT 6240

(all revision letters) (all revision letters)

(all revision letters)

WARNING:

If the pump is dropped or hit, inspect the pump for damage. Do not use a pump

that is damaged or is not functioning properly. Contact Customer Service to

return a pump for service.

If the pump is dropped or hit, the battery door may become broken or damaged.

Do not use the pump if the battery door is damaged because the battery will not

be properly secured; this may result in loss of power or non-delivery of drug.

Do not disclose to the patient the pump’s security codes or any other information

that would allow the patient complete access to all programming and operating

functions.

You must use a CADD

extension set with anti-siphon valve or a CADD

administration set with either an integral or an add on anti-siphon valve to

protect against unregulated gravity infusion that can result from

an improperly attached cassette.

IN19822.indd 1

10/24/2011 3:57:07 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды