Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 15

Страница: 15 / 64

General Description and Basic Operations

Section 1

Basic Oper

ations

Changing the Lock Level

Before programming the pump, make sure the lock level is LL0 so you

can access all programming screens.

After programming, the lock level must be changed to LL1 or LL2 to

prevent the patient from having complete access to all programming and

operating functions.

If AutoLock is not in use and the lock level is LL0 when you attach a

cassette, the message “AutoLock not in use / Change Lock Level from

LL0?” will appear; this allows you to set the lock level to LL1 or LL2 with

the steps below. For detailed information on lock levels, see page 8.

NOTE: You may change the lock level at any time by stopping the pump and

pressing

. Then begin with step 2 below.

To change the lock level

1. With this message displayed, press

. (If you do not wish to change the

lock level at this time, press

2. The current lock level will appear.

3. Press

until the desired lock

level (LL1 or LL2) appears.

4. Press

again. “000” will appear.

5. Press

until the Lock Level

Code appears.

6. Press

to set the new lock level.

Watch the display to verify that the

correct lock level is being entered.

Lock Level

LL1

<Changing...>

AutoLock not in use.

Change Lock Level

from LL0?

Press Y or N

Lock Level

LL0

Lock Level

LL1

Lock Level Code

000

Lock Level Code

XXX

IN19822.indd 9

10/24/2011 3:57:09 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды