Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 45

Страница: 45 / 64

Section 3

Medication Reservoir or Administration Set

Section 3

Reserv

oir or

Admin Set

Priming the Tubing and Connecting to the Patient

If the lock level is LL0 or LL1 when you

attach a cassette, “Prime Tubing?” will

appear in the sequence of screens. Prime

the tubing before connecting it to the

patient’s infusion set or indwelling catheter.

NOTE: If you are not changing the cassette but wish

to prime the fluid path, you may use the Prime

option. To prime, select Prime from the Options menu,

then follow the steps below, beginning with step 2.

WARNING:

Do not prime the fluid path with the

tubing connected to a patient as this could result in

over-delivery of medication or air embolism.

To prime the tubing and connect to the patient

1. When “Prime Tubing?” appears,

press

2. Make sure the tubing is disconnected

from the patient and the tubing clamp

is open.

3. Press and hold the

key until the

tubing is fully primed or until priming

stops.

NOTE: Fluid delivered during priming is

subtracted from the reservoir volume, but is

not added to the Given screen since this fluid

is not delivered to the patient.

4. If the tubing is not yet fully primed,

press

and repeat step 3.

When the tubing is fully primed,

press

to exit priming.

Prime Tubing?

Press Y or N

Prime Tubing?

Press Y or N

Disconnect tubing

from patient

Open clamps

Hold Y to prime

Priming...

0.1 ml

Hold Y to prime

Continue Priming?

Press Y or N

IN19822.indd 39

10/24/2011 3:57:18 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды