Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 11

Страница: 11 / 64

General Description and Basic Operations

Section 1

Basic Oper

ations

Door w/Button»

«Prizm Match

Battery»

Installing a Battery

Use a fresh, 9 volt alkaline or lithium battery such as the DURACELL

Alkaline MN 1604 or the ULTRALIFE

Lithium U9VL battery. The pump

retains all programmed values while the battery is removed. If the pump

is running, you may connect an external power source to keep the pump

running for 3 minutes while you change the battery.

CAUTION:

Do not store the pump for prolonged periods with the battery installed. Battery

leakage could damage the pump.

WARNING:

If the pump is dropped or hit, inspect the pump for damage. Do not use a pump

that is damaged or is not functioning properly. Contact Customer Service to

return a pump for service.

If the pump is dropped or hit, the battery door may become broken or damaged.

Do not use the pump if the battery door is damaged because the battery will not

be properly secured; this may result in loss of power or non-delivery of drug.

There is no pump alarm to alert users that a battery has not been properly

installed or has become dislodged. An improperly installed or dislodged battery

could result in loss of power and non-delivery of drug.

Do not use rechargeable NiCad or nickel metal hydride (NiMH) batteries. Do not

use carbon zinc (“heavy duty”) batteries. They do not provide sufficient power

for the pump to operate properly.

To install a battery

1. Make sure the pump is stopped. Press the

button on the battery door and slide the

battery door forward. Remove the

used battery.

2. Match the + and - markings on the new

battery with the markings on the pump.

Insert the battery. The pump will beep if the

battery is inserted correctly.

3. Replace the battery door.

IN19822.indd 5

10/24/2011 3:57:08 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды