Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 29

Страница: 29 / 64

Pump Programming - Continuous Delivery Mode

Section 2

Pump

ogr
amming

CONTIN: Programming with Upper Limits,

Adjusting Rate in Lock Level 1

If a prescription allows for the continuous rate to be adjusted during the

course of therapy, you may wish to operate the pump in LL1. Then, when

necessary, you can adjust the continuous rate up to the maximum value

that was programmed in LL0.

Programming the pump to use this feature

1. During initial programming in LL0,

enter the upper limit value for the

continuous rate. (This will be the

maximum value when the pump is

in LL1.)

2. After you are fi nished programming,

change the lock level to LL1.

3. Decrease the continuous rate to

its starting value. “Range: Limited”

indicates you cannot increase the

value beyond the maximum

programmed in LL0.

Adjusting the rate while the pump is in use

If it becomes necessary to increase the continuous rate during the

course of therapy, stop the pump but remain in LL1.

1. Press

„

until the Continuous Rate

screen appears.

2. Press

to select the desired

value, then press

€

“Range: Limited” indicates you

cannot increase the value beyond

the maximum.

3. Restart the pump if appropriate.

Continuous Rate

| 5.0 ml/hr

<Range: 0 - 350.0>

Continuous Rate

| 2.5 ml/hr

<Range: Limited>

Continuous Rate

| 5.0 ml/hr

<Range: Limited>

IN19822.indd 23

10/24/2011 3:57:13 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды