Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 44

Страница: 44 / 64

Section 3

Medication Reservoir or Administration Set

5. Gently twist and pull on the cassette

to make sure it is firmly attached.

6. If “Reset Reservoir Volume to...?”

appears,

Press

to reset Reservoir

Volume to the value shown, or

Press

to retain the current

value.

NOTE: If this screen does not appear,

reservoir volume may already be reset.

If this message appears, the

pump is in the TPN delivery mode

and reservoir volume is not in use.

Press

to reset the infusion

profile.

7. If you have reset the reservoir

volume and the pump is in the TPN

delivery mode, “Infusion Profile has

been reset” will also appear.

Infusion Profile

has been reset

Reset Infusion
Profile?

Press Y or N

Reset Reservoir
Volume to 100.0 ml?

Press Y or N

IN19822.indd 38

10/24/2011 3:57:18 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды