Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 58

Страница: 58 / 64

Section 5

Accessories

3. Hold the pump firmly against the

security shell. Insert the key into the

lock on the back of the security shell

and turn it counterclockwise until the

black mark lines up with “Locked.”

Make sure the pump is firmly locked

into place.

Removing the pump and the fluid bag or syringe

1. Insert the key into the lock. Turn the key clockwise until the pump

unlocks from the security shell.

2. Remove the pump and the fluid bag or syringe.

Using the Lockable Polemount Bracket

For use with the CADD-Prizm

VIP pump or the security shell

The lockable polemount bracket allows you to lock a CADD-Prizm

VIP

pump onto an IV pole. It is designed to attach directly to the back of a

CADD-Prizm

VIP pump or a CADD-Prizm

VIP pump security shell. Using

a CADD

key, you can lock the bracket in place so that neither the pump

nor the polemount bracket can be removed from the IV pole.

CAUTION: If you use the EPS System power pack with a pump mounted on an IV pole,

do not allow the power pack to hang from the pump’s connector. This could result in

damage to the power pack or pump connector.

If you wish to use an external source of power with the CADD-Prizm

VIP

pump while it is mounted on an IV pole, it is recommended that you use

the AC adapter without the power pack.

To attach the pump or security shell to a pole using the

polemount bracket

NOTE: If you are using a security shell, you may first mount the security shell to the

polemount bracket following these instructions, then install the pump and IV bag or

sterile vial with injector (syringe) into the security shell.

1. Place the polemount bracket around the IV pole at the

desired height. Clamp the bracket firmly to the pole by turning

the knob clockwise.

IN19822.indd 52

10/24/2011 3:57:21 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды