Smiths Medical CADD-Prizm VIP 6100 Скачать руководство пользователя страница 24

Страница: 24 / 64

Section 2

Pump Programming - PCA Delivery Mode

PCA: Starting a Clinician Bolus

1. Make sure the pump is running (in any

lock level). Start the pump if necessary.

2. Press

3. Press

until the clinician bolus

code appears on the display

(See Operator’s Manual).

4. Press

again.

WARNING:

To prevent the patient from

accessing the clinician bolus function,

do not let the patient know the

clinician bolus code.

5. Press

to select the

desired amount.

6. Press

€

NOTE: If you enter a value of 100, a screen

will appear asking you to confi rm the value.
Press

to confi rm, or

to re-enter

the value.

7. The screen will show the amount

decreasing as the bolus is delivered.

PCA: Starting a demand dose

If a demand dose has been programmed, the patient may start a

demand dose while the pump is running. If no demand dose has been

programmed, the pump will display the message “Dose not delivered,

No Dose programmed.”

1. Make sure the pump is running

(in any lock level). Start the pump if

necessary.

2. Press

(or the button on the

remote dose cord, if attached). Two

beeps will sound and the pump will

begin delivering the demand dose.

As the demand dose is delivered, the

main screen will show “DOSING” in

place of “RUNNING.”

Clinician Bolus Code

XXX

Clinician Bolus

| 10.00 mg

Range <0 - 20.00>

Demand Dose

Started

NEXT to continue

*** PCA 6210X ***
Low Battery DOSING
Res Vol 47.0 ml
Press NEXT to advance

Clinician Bolus

10.00 mg

<Delivering...>

IN19822.indd 18

10/24/2011 3:57:11 PM

Содержание CADD-Prizm VIP 6100

































































Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды

Smiths Medical CADD-Prizm VIP 6100, Руководство пользователя

Результаты поиска

Содержание CADD-Prizm VIP 6100

Отзывы:

Похожие инструкции для CADD-Prizm VIP 6100

Бренды по названию

Популярные бренды