Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 71

Страница: 71 / 343

Section 02 ENGINE

Subsection 06 (E-RAVE SYSTEM)

A35C0OA

1. Gears aligned

After assembly, check for smooth mechanical
movement of the E-RAVE system.

E-RAVE HOUSING

Removal

Remove the following:

E-RAVE cables

no. 4

Cover

no. 11

NOTE:

E-RAVE housing with shaft and E-RAVE

valves can be removed altogether if desired.

A35C0NA

Drive gears

no. 7

Inspection

Check housing condition.

Installation

Reverse removal steps.

E-RAVE VALVES

Removal

Remove the following:

Cover

no. 11

Drive gears

no. 7

Housing

no. 10

Inspection

Clean carbon deposits on parts. Check gears con-
dition.

Installation

Reverse removal steps.

mmr2005-148

Содержание 2005 MACH Z
























































































































































































































































































































































Результаты поиска

Содержание 2005 MACH Z

Отзывы:

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 71 / 343

Результаты поиска

Содержание 2005 MACH Z

Отзывы: