Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 145

Страница: 145 / 343

Section 04 ENGINE MANAGEMENT (SDI)

Subsection 02 (DIAGNOSTIC PROCEDURE)

EMS Fault Code Table

P CODE

EMS PILOT LAMP

BEEPER

DESCRIPTION

P0106

OFF

Air pressure sensor voltage out of range.

P0337

OFF

No crankshaft signal detected.

P0336

OFF

High engine RPM detected.

P0339

OFF

Crankshaft signal fault.

P0654

OFF

Tachometer RPM signal shorted to battery.

P0654

OFF

Tachometer RPM signal open circuit or shorted to
ground.

P0617

OFF

Starter relay shorted to battery.

P0616

OFF

Starter relay open circuit or shorted to ground.

P1670

OFF

Beeper shorted to battery.

P1671

OFF

Beeper open circuit or shorted to ground.

P0650

OFF

EMS pilot lamp shorted to battery.

P0650

OFF

EMS pilot lamp open circuit or shorted to ground.

P1675

OFF

Relay 2 shorted to battery.

P1676

OFF

Relay 2 open circuit or shorted to ground.

P1148

OFF

Safety fuel cut off detected.

P1611

OFF

P+ Test of ISC output signal failed.

P0513

OFF

Incorrect DESS

key.

P0601

OFF

Faulty module (software of hardware damaged).

P1677

OFF

Relay 3 shorted to battery.

P1678

OFF

Relay 3 open circuit or shorted to ground.

P1648

OFF

Battery lamp shorted to battery.

P1649

OFF

Battery lamp open circuit or shorted to ground.

P0655

OFF

Engine temperature lamp shorted to battery.

P0655

OFF

Engine temperature lamp open circuit or shorted to
ground.

P1646

OFF

Engine temperature lamp shorted to battery.

P1647

OFF

Engine temperature lamp open circuit or shorted to
ground.

P0648

OFF

DESS lamp shorted to battery.

P0648

OFF

DESS lamp open circuit or shorted to ground.

P1654

OFF

Oil lamp shorted to battery.

P1658

OFF

Oil lamp open circuit or shorted to ground.

P0117

BLINK

OFF

Engine temperature sensor voltage too low.

130

mmr2004-125

Содержание 2005 MACH Z
























































































































































































































































































































































Результаты поиска

Содержание 2005 MACH Z

Отзывы:

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 145 / 343

Результаты поиска

Содержание 2005 MACH Z

Отзывы: