Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 132

Страница: 132 / 343

Section 03 FUEL SYSTEM

Subsection 01 (FUEL TANK AND FUEL PUMPS)

DIAPHRAGM FUEL PUMP
CLEANING AND INSPECTION

The entire pump should be cleaned with general
purpose solvent before disassembly.

Fuel pump components should be cleaned in gen-
eral purpose solvent and dried with compressed
air.



WARNING

Solvent with low flash point such as gasoline,
naphtha, benzol, etc, should not be used as
each is flammable and explosive.

Inspect diaphragm. The pumping area should be
free of holes, tears or imperfections. Replace as
needed.

DIAPHRAGM FUEL PUMP
INSTALLATION

For installation, reverse the removal process but
pay attention to the following.



WARNING

Pressure test to ensure there is no leak in fuel
system.

Respect the following tightening torque specifica-
tion:

DESCRIPTION

TIGHTENING TORQUE

Pump retaining screws

5 N•m (44 lbf•

)

116

mmr2005-123

Содержание 2005 MACH Z
























































































































































































































































































































































Результаты поиска

Содержание 2005 MACH Z

Отзывы:

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 132 / 343

Результаты поиска

Содержание 2005 MACH Z

Отзывы: