background image

Section 01 MAINTENANCE

Subsection 02 (STORAGE)

To clean the entire vehicle, including bottom pan
and metallic parts use heavy duty cleaner (spray
can 400 g) (P/N 293 110 001) or heavy duty cleaner
(4 L) (P/N 293 110 002).

CAUTION:

Do not use Heavy duty cleaner on

decals or vinyl.

For vinyl and plastic parts use vinyl & plastic clean-
er (6 x 1 L) (P/N 413 711 200).

To remove scratches on windshield or hood use
BOMBARDIER scratch remover kit (P/N 861 774
800).

CAUTION:

Never clean plastic parts or hood

with strong detergent, degreasing agent, paint
thinner, acetone, products containing chlorine,
etc.

Inspect the hood and repair any damage.

Touch up all metal spots with touch-up paint
where paint has been scratched off.

Spray all bare metal parts including shock chromed
rods with BOMBARDIER LUBE (P/N 293 600 016).

Wax the hood and the painted portion of the
frame for better protection. Use a non-abrasive
wax such as silicone wax.

NOTE:

Apply non-abrasive wax on glossy finish

only.

Vehicle Protection

Protect the vehicle with a cover to prevent dust
accumulation during storage.

CAUTION:

The snowmobile has to be stored

in a cool and dry place and covered with an
opaque but ventilated tarpaulin. This will pre-
vent sun rays and grime from affecting plastic
components and vehicle finish.

Lift rear of vehicle until track is clear of the ground.
Install on a snowmobile mechanical stand.

NOTE:

Do not release track tension.

6

mmr2005-111

Содержание 2005 MACH Z
























































































































































































































































































































































Отзывы: