Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 42

Страница: 42 / 343

Section 02 ENGINE

Subsection 02 (AIR INTAKE SYSTEM)

A35C07A

1. Adaptor plate
2. Locking tab
3. Air intake silencer

AIR INTAKE SILENCER
INSTALLATION (ENGINE SIDE)

The installation is the reverse of the removal pro-
cedure.

ADAPTOR PLATE REMOVAL

Open LH side panel.

Remove air intake silencer (engine side), refer to
procedure above.

Unscrew clamps from throttle body.

Remove adaptor plate.

A35C08A

1. Clamps
2. Adaptor plate

ADAPTOR PLATE INSTALLATION

The installation is the reverse of the removal pro-
cedure.

INTAKE DEFLECTOR/FILTER
REMOVAL

Open LH side panel.

Remove air intake silencer (body side), refer to
procedure above.

Remove push nuts retaining intake deflector to LH
side panel.

A35C09A

1. Push nuts

mmr2005-149

Содержание 2005 MACH Z
























































































































































































































































































































































Результаты поиска

Содержание 2005 MACH Z

Отзывы:

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 42 / 343

Результаты поиска

Содержание 2005 MACH Z

Отзывы: