manualshive.com logo in svg

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 262 / 343

Поделиться
Скачать
Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 262

Section 07 REAR SUSPENSION

Subsection 01 (SC SUSPENSION)

A33F5SA

2

1

TYPICAL

1. Track window
2. Slider shoe

Using a pry bar or screw driver, push slider shoe
until it comes in contact with track.

A33F5TA

TYPICAL — PUSH ON SLIDER SHOE

Using locking pliers, pull slider shoe thru track win-
dow to remove.

NOTE:

If necessary, lubricate track window to fa-

cilitate slider shoe removal.

A33F5UA

TYPICAL — PULL ON SLIDER SHOE TO REMOVE

SLIDER SHOE INSTALLATION

Installation is reverse of removal procedure. Pay
attention to the following details.

Make sure to insert slider shoe end with hole first.

Respect the following tightening torque specifica-
tion:

DESCRIPTION

TIGHTENING TORQUE

Slider shoe nut

2.5 N•m (22 lbf•

in

)

FRONT ARM REMOVAL

NOTE:

Front arm can be removed with suspen-

sion in place.

Lift rear of vehicle and support it off the ground.

Remove the following:

– shock upper bolt and nut
– front arm lower bolts and washers
– unfasten one end of stopper strap(s)
– remove front arm upper bolts, nuts and wash-

ers.

Remove front arm.

mmr2005-147

251

Содержание 2005 MACH Z
























































































































































































































































































































































Отзывы:

Нет отзывов