Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 271

Страница: 271 / 343

Section 07 REAR SUSPENSION

Subsection 02 (SC 4 SUSPENSION)

A35F01B

TYPICAL

1. Rear shock absorber
2. Remove bolts and nuts

Using a punch, remove lower shock bar axle.

Pay attention to plastic spacers.

Remove shock.

A33F5KA

TYPICAL — REMOVE BAR AXLE

REAR SHOCK ABSORBER
INSTALLATION

Installation is reverse of removal procedure. Pay
attention to the following details.

To ease shock installation, secure upper shock
first.

CAUTION:

Make sure shock bar axle is aligned

with swivel bushings before inserting it.

A35F0BA

1. Bar axle
2. Swivel bushings
3. Plastic spacers

FRONT SHOCK ABSORBER
REMOVAL

Lift rear of vehicle and support it off the ground.

Unfasten one end of stopper straps.

A33F5MA

TYPICAL

1. Unfasten one end of stopper straps

Remove bolts and nuts from shock.

NOTE:

If necessary, remove idler wheel(s) to ease

lower shock component removal.

260

mmr2005-139

Содержание 2005 MACH Z
























































































































































































































































































































































Результаты поиска

Содержание 2005 MACH Z

Отзывы:

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 271 / 343

Результаты поиска

Содержание 2005 MACH Z

Отзывы: