manualshive.com logo in svg

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 310 / 343

Поделиться
Скачать
Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 310

Section 08 STEERING/FRONT SUSPENSION

Subsection 02 (FRONT SUSPENSION)

1

A33F22A

A

1. Tool perpendicular (90°) to torque wrench

A. 90°

A33F2KA

Use ball joint lock tool (P/N 529 035 945) to restrain
ball joint during nut tightening.

NOTE:

The upper arm ball joint has to be removed

in order to use this tool. Also remove the small
screw from top of ball joint to allow proper seating
of tool.

A32F3XA

TYPICAL

Anti-Sway Bar

Summit

Notice that LH and RH sliding blocks are different.
Look for their molded identification with LH or RH
letters.

1

A33F2DA

1. Molded identification for proper side installation

To install sliding blocks:

– Temporarily rotate the rear block by 180°.
– Insert on anti-sway bar end and push beyond

the lower arm.

– Rotate block back by 180° to its normal position.
– Install the other block half.
– Install screws and nuts.
– Ensure blocks slide easily when compressing

and releasing suspension.

302

mmr2005-142

Содержание 2005 MACH Z
























































































































































































































































































































































Отзывы:

Нет отзывов