manualshive.com logo in svg

Ski-Doo 2005 MACH Z, Руководство по ремонту, Страница: 249 / 343

Поделиться
Скачать
Ski-Doo 2005 MACH Z Скачать руководство пользователя страница 249

Section 06 DRIVE SYSTEM

Subsection 07 (DRIVE AXLE)

A33D0OA

The bearing

no. 9

must have its shield facing the

sprocket.

The drive axle bearing in chaincase must have its
shield facing right side (cover).

Index speedometer magnetic adapter

no. 4

in

drive axle and push until it is completely inserted
in its hole.

LUBRICATION

Lubricate end housing bearing with synthetic
grease (P/N 219 700 417).

Continue lubricat-

ing until grease flows out of the pilot hole on
speedometer sensor.

A32D44A

1

TYPICAL

1. Lubricate until grease flows out here

ADJUSTMENT

Sprocket/Track Alignment

CAUTION:

Do not tamper with sprocket/track

alignment if frame or suspension is damaged.

Sprockets may be repositioned to fit lugs without
removing drive axle.

Use drive axle sprocket adjuster kit (P/N 861 725
700).

A33D0PA

TYPICAL

238

mmr2005-137

Содержание 2005 MACH Z
























































































































































































































































































































































Отзывы:

Нет отзывов