Siemens RVL481 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 118

background image

97/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

26 Function block "D.h.w. solar charging"

20.05.2008

26.2.8 Maximum

limitation

of charging temperature

Operating line 206 allows for setting the maximum limitation for charging temperature.
The collector pump is switched off if the maximum charging temperature in the storage
tank is reached.

T

ON

OFF

TSpMax

t

254

1D

12

1 K

TSp

TSp

Storage tank temperature

TSpMax

Maximum limitation of the charging temperature-

ON/OFF Collector

pump

T Temperature
t Time

•

Charging is stopped if the storage tank temperature exceeds the maximum limita-

tion:
TSp > TSpMax

•

Charging is again released if the storage tank temperature drops below the maximum

limitation by 1 K:
TSp < TSpMax – 1 K

The collector overheating protection function can again activate the collector pump until
the storage tank temperature maximum limitation is reached.

26.2.9 Storage tank temperature maximum limitation

Operating line 207 allows for setting the d.h.w. storage tank temperature maximum
limitation.
The storage tank is never charged in excess of the set temperature (refer to
section "26.2.5 Collector temperature to protect against overheating").

The storage tank maximum limitation function is not a safety function!

Note

Caution

«
...
95
96
97
98
99
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: Vacon Страницы: 62

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 7

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Radware Страницы: 98

Бренд: Rain Bird Страницы: 138

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: Barco Страницы: 4

Бренд: Ulvac Страницы: 48

Бренд: Belimo Страницы: 2

Бренд: Delta Regis Страницы: 15

Бренд: Belimo Страницы: 10

Бренд: TA Страницы: 4

HELENOS V DC 2005DP.2-01

Бренд: Heinzmann Страницы: 66

ENVIROMUX-STSP-SL-7

Бренд: NTI Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды