Siemens RVL481 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 118

background image

62/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

16 Function block "Basic settings d.h.w."

20.05.2008

16

Function block "Basic settings
d.h.w."

Function block "Basic settings d.h.w." is used to select the heating circuits for which
the d.h.w. is heated and according to which program the d.h.w. circulating pump shall
operate.

16.1 Operating

lines

Line Function, parameter

Factory setting (range)

Unit

121

Assignment of d.h.w. heating

0 (0…2)

122

Program for the circulating pump

2 (0…3)

16.2 Assignment of d.h.w. heating

Operating line 121 is used to select for which heating circuits the d.h.w. is heated, that
is, which heating circuits draw their water from the same source.

Operating line 121 Explanation

0

D.h.w. heating is only provided for the heating circuit associated
with the own controller.
With plant types 4–x, 5–x, and 6–x, this setting makes no sense
since no own heating circuit exists (no d.h.w. in that case).

1

D.h.w. heating is only provided for the heating circuits of the con-
trollers

with the same segment number

that are connected to

the data bus (LPB).

2

D.h.w. heating is provided for

all

heating circuits of the controllers

connected to the data bus (LPB).

The setting is required in connection with operating lines 122 (circulating pump pro-
gram) and 123 (release of d.h.w. heating).

16.3 Program for the circulating pump

16.3.1 General mode of operation

On operating line 122, it is possible to enter according to which time program the d.h.w.
circulating program shall operate. The use of a circulating pump is optional with all
types of plant.

With d.h.w. plant type x–4 ”Instantaneous d.h.w. heating via heat exchanger”, it
is strongly recommended to use a circulating pump, the reason being better
control performance.

That circulating pump runs only when d.h.w. heating is switched on (button is lit).
The circulating pump runs at the following times, depending on the setting made on
operating line 122:

Operating line 122

The circulating pump runs

0

Continuously (24 hours a day)

1

According to one or several heating programs

2

According to switching program 2 of own controller

3

According to switching program 3 of own controller

With setting 1, operation of the circulating pump depends on the setting made on oper-
ating line 121. In an interconnected plant with several controllers, that is, with several
heating programs, the circulating pump runs when at least one of the controllers pro-

Important

«
...
60
61
62
63
64
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: Galcon Страницы: 32

Бренд: Yudian Страницы: 26

Бренд: Gatekeeper Страницы: 28

Бренд: ABB Страницы: 17

Бренд: Nemesis Страницы: 6

Vertical Fan Coil

Бренд: Solaris Страницы: 10

Бренд: S&C Страницы: 24

Бренд: Olsen Страницы: 4

Бренд: DAPAudio Страницы: 11

Бренд: Akytec Страницы: 15

Бренд: LAE electronic Страницы: 4

Бренд: Ledj Страницы: 12

Бренд: Parker Страницы: 31

Mannesmann DKC21.3

Бренд: Rexroth Indramat Страницы: 38

Max Charge MC-614-H

Бренд: Balmar Страницы: 20

Бренд: Trane Страницы: 60

Бренд: Pilz Страницы: 23

Бренд: Galletti Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды