Siemens RVL481 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 118

background image

66/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

17 Function block "Release of d.h.w. heating"

20.05.2008

17.2.2 Release

programs

Depending on the setting made on operating line 123, release of d.h.w. heating takes
place at the following times:

Setting

D.h.w. heating is released

0

Continuously (24 hours a day)

1

According to one or several heating programs

2

According to switching program 2 of own controller

With setting 1, d.h.w release depends on the setting made on operating line 121. In an
interconnected system of several controllers, that is, in the case of several heating
programs, the circulating pump runs if at least one of the connected controllers pro-
vides heating to the NORMAL temperature according to its heating program (independ-
ent of the operating mode), and is not in holiday mode.
Release of d.h.w. heating is shifted forward in time by one hour against the times of the
heating program. If optimum start control is active, the optimized switch-on times are
used – and not the times entered.
With plant types 4–x, 5–x, and 6–x, and the setting of 0 (own controller) on operating
line 121, d.h.w. heating will never be released since these plant types have no own
heating program.
The release of d.h.w. heating is explained using 2 examples, in which controllers A, B,
C and D are interconnected via the data bus:

Operating line

121 123

Con-
trollers

Operating
mode

Heating program, optimi-
zation, holidays

Release

A

06:00…18:00,
no optimization

B

07:00…23:00

C

07:00…22:00, optimum
start control shifts forward
by 2 hours

2 1

D

03:00…22:00, HOLIDAYS

D.h.w. heating
is released from
04:00 to 23:00

Operating line

121 123

Con-
trollers

Operating
mode

Heating program, optimi-
zation, holidays

Release

A

06:00…18:00,
no optimization

B

08:00…23:00

C

07:00…22:00, optimum
start control shifts forward
by 2 hours

2

1

D

05:00…21:00

D.h.w. heating
is released
from 04:00 to
23:00

17.2.3 D.h.w heating during the holiday period

In holiday mode, d.h.w. heating is provided as follows:

Operating

line 121

Operating

line 123

D.h.w. heating

0

0, 1, or 2

No d.h.w. heating when own controller is in
holiday mode

1

0, 1, or 2

No d.h.w. heating when all controllers in the
same segment are in holiday mode

2

0, 1, or 2

No d.h.w. heating when all controllers in the
interconnected system are in holiday mode

Example 1

Example 2

«
...
64
65
66
67
68
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: Yardney Страницы: 8

Бренд: J3C Страницы: 2

Бренд: Magnescale Страницы: 3

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

Бренд: Nice Страницы: 32

Бренд: Danfoss Страницы: 10

Enclosure ENCR-10

Бренд: suprema Страницы: 18

Бренд: R-Tec Страницы: 14

ERO-32AP-0 V1.4

Бренд: Darco Страницы: 14

Бренд: Rainmachine Страницы: 22

Бренд: Estyma Страницы: 56

Hauser COMPAX-M Series

Бренд: Parker Страницы: 84

Бренд: Danfoss Страницы: 44

Бренд: Samson Страницы: 72

Бренд: MULTISPAN Страницы: 2

Бренд: Omron Страницы: 25

Бренд: Trane Страницы: 60

Governor TEN014980

Бренд: Gardner Denver Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды