Siemens RVL481 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 118

background image

55/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

12 Function block "Boiler"

20.05.2008

12.4.5 Protection

against

boiler overtemperatures

To prevent heat from building up in the boilers (protection against overtemperatures),
the RVL481 offers a protective function.
When the first burner stage is switched off, the controller allows pump M1 to overrun for
the set pump overrun time (operating line 174 on the boiler temperature controller),
generating at the same time a forced signal to all loads (inside the controller on the
data bus). If the boiler temperature controller is located in segment “0”, the forced sig-
nal will be delivered to all loads in all segments. By contrast, if the boiler temperature
controller is located in segment 1…14, the signal will only be sent to the loads in the
same segment.

Boiler controller, stage 1

Forced signal

Overrun time
of boiler pump

Pump

Off

Y

t Time
Y

Control signal boiler pump

All loads (heating and d.h.w. circuits) and heat converters that abruptly reduce their
demand for heat watch the data bus during the set pump overrun time to see if a forced
signal is being sent by the boiler.

•

If no forced signal is received, the consumers and heat converters only allow pump

overrun to take place (refer to section “25.4.4 Pump overrun“)

•

If, in this time window, a forced signal is received, the loads continue to draw heat from

the boiler in the following manner:

−

Plant types with heating circuits using a mixing valve maintain the previous set-
point

−

Plant types with pump heating circuits allow the pumps to continue running

D.h.w. plant type 4 (instantaneous d.h.w. heating via heat exchanger) does not respond
to forced signals since it can draw heat from the boiler only if there is demand for d.h.w.
If the boiler sets the forced signal to zero, the loads and heat exchanges that have
responded to the forced signal respond as follows:

•

They close their mixing valves

•

Their pumps run for the set pump overrun time and then stop

D.h.w. discharging protection has priority over protection against boiler overtempera-
tures.

12.5 Operating mode of pump M1

The operating mode during protective boiler start-up of pump M1 must be selected on
operating line 99:

•

Circulating pump with no deactivation (setting 0):

The circulating pump runs when one of the consumers calls for heat and when burner
stage 1 is switched on, that is, also during protective boiler startup.

•

Circulating pump with deactivation (setting 1):

The circulating pump runs when one of the consumers calls for heat. It is deactivated
during protective boiler startup.

«
...
53
54
55
56
57
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: ZirbenLüfter Страницы: 36

Бренд: Galaxy Control Systems Страницы: 5

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 26

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Kantronics Страницы: 201

Бренд: SFC Страницы: 48

Бренд: Satel Страницы: 8

Бренд: Taylor Страницы: 34

Бренд: Azbil Страницы: 68

Бренд: Ltech Страницы: 2

Бренд: Qorvo Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды