Siemens RVL481 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 118

background image

38/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

10 Function block "Space heating"

20.05.2008

The heating will be switched on again only when

all

3 of the following conditions are

satisfied:

•

The actual outside temperature has fallen 1 °C below the current ECO heating limit

•

The composite outside temperature has fallen 1 °C below the current ECO heating

limit

•

The attenuated outside temperature has fallen 1 °C below the "ECO day" heating limit

10.2.4 Operating

modes and operating states

The ECO function is performed depending on the operating mode:

Operating mode or operating state

ECO function

Current heating limit

Automatic operation

active

ECO day or ECO night

Continuously REDUCED heating active

ECO night

Continuously NORMAL heating

inactive

–

Protection mode / holiday mode

active

ECO night

Manual operation

inactive

–

10.3 Room temperature source

The outside temperature source can be selected on operating line 65.
The following settings are available:

Operating line 65 SET

Room temperature source

0

No room sensor

1

Room unit at terminal A6

2

Room sensor connected to terminal B5

3

Average of devices connected to A6 and B5

A Automatic

selection

Operating line 65 also displays the room temperature source actually used by the con-
troller (

ACTUAL

).

ACTUAL = 0  controller operates without a sensor
ACTUAL = 1  controller operates with a room unit connected to terminal A6
ACTUAL = 2  controller operates with a room sensor connected to terminal B5
ACTUAL = 3  controller operates with the mean value of the devices connected to A6

and B5

10.4 Optimization

10.4.1 Definition

and

purpose

Operation of the heating system is optimized. According to EN 12 098, optimization is
the "automatic shifting of the switch-on and switch-off points aimed at saving energy".
This means that:

•

Switching on and heating up as well as switching off are controlled such that during

building occupancy times the required room temperature level will always be ensured

•

The smallest possible amounts of energy will be used to achieve this objective

10.4.2 Fundamentals

It is possible to select or set:

•

The type of optimization: either with a room sensor / room unit or based on the room

model

•

The maximum limit value for the heating-up time

•

The maximum limit value for optimum shutdown

•

Quick setback: Yes or no

Switching the heating on

«
...
36
37
38
39
40
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Jands Страницы: 6

Бренд: SOMFY Страницы: 4

Бренд: Shimaden Страницы: 16

KaDe KDH-KZ620U

Бренд: AAT Holding Страницы: 28

Бренд: Brooks Страницы: 68

lyriQ AU7394 Series

Бренд: On-Q Страницы: 8

Бренд: ULTRAFRYER Страницы: 1

Бренд: Hall Research Technologies Страницы: 16

MotionWorks IEC

Бренд: YASKAWA Страницы: 21

Бренд: Canford Страницы: 2

Бренд: Dontek Страницы: 2

Бренд: Mitsubishi Страницы: 4

Бренд: Salus Страницы: 24

Бренд: Suzhou MONARCH Control Technology Co., Ltd. Страницы: 233

Бренд: Grundfos Страницы: 348

Бренд: Gembird Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды