Siemens RVL481 Скачать руководство пользователя страница 9

Страница: 9 / 118

9/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

Contents

20.05.2008

25.3.2

Relay test....................................................................................................... 84

25.3.3

Sensor test .................................................................................................... 85

25.3.4

Test of H–contacts......................................................................................... 86

25.4

Auxiliary functions.......................................................................................... 86

25.4.1

Frost protection for the plant.......................................................................... 86

25.4.2

Flow alarm ..................................................................................................... 86

25.4.3

Manual overriding of operating mode (contact H1) ....................................... 87

25.4.4

Pump overrun ................................................................................................ 87

25.4.5

Pump kick ...................................................................................................... 88

25.4.6

Winter- / summertime changeover ................................................................ 88

25.4.7

Gain of locking signal .................................................................................... 88

25.5

Entries for LPB .............................................................................................. 89

25.5.1

Source of time of day..................................................................................... 89

25.5.2

Outside temperature source .......................................................................... 90

25.5.3

Addressing the devices ................................................................................. 90

25.5.4

Bus power supply .......................................................................................... 91

25.5.5

Bus loading number....................................................................................... 91

25.6

Heat demand output DC 0…10 V.................................................................. 91

Function block "D.h.w. solar charging" .................................................... 92

26.1

Operating lines .............................................................................................. 92

26.2

Functions ....................................................................................................... 92

26.2.1

Temperature differential ON/OFF solar ......................................................... 92

26.2.2

Minimum charging temperature..................................................................... 93

26.2.3

Minimum runtime ........................................................................................... 94

26.2.4

Collector frost protection temperature ........................................................... 94

26.2.5

Collector temperature to protect against overheating.................................... 95

26.2.6

Storage tank recooling................................................................................... 95

26.2.7

Evaporation temperature of heat carrier........................................................ 96

26.2.8

Maximum limitation of charging temperature................................................. 97

26.2.9

Storage tank temperature maximum limitation .............................................. 97

26.2.10

Collector start function gradient..................................................................... 98

Function block "Locking functions".......................................................... 99

27.1

Operating line ................................................................................................ 99

27.2

Locking the settings on the software side...................................................... 99

27.3

Locking the settings for district heat on the hardware side............................ 99

Communication ......................................................................................... 100

28.1

Combination with room units ....................................................................... 100

28.1.1

General........................................................................................................ 100

28.1.2

Combination with room unit QAW50 ........................................................... 100

28.1.3

Combination with room unit QAW70 ........................................................... 101

Содержание RVL481























































































































Результаты поиска

Содержание RVL481

Отзывы:

Похожие инструкции для RVL481

Бренды по названию

Популярные бренды

Siemens RVL481, Основная документация

Результаты поиска

Содержание RVL481

Отзывы:

Похожие инструкции для RVL481

Бренды по названию

Популярные бренды