Siemens RVL481 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 118

background image

31/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

6 Function block "Enduser d.h.w."

20.05.2008

6

Function block "Enduser d.h.w."

This function block contains settings for d.h.w. heating that the enduser himself can
make.

6.1 Operating

lines

Line Function, parameter

Factory setting (Range)

Unit

26

Setpoint of NORMAL d.h.w. temperature

55 (20…100)

°C

27 D.h.w.

temperature

Display

function

28

Setpoint of REDUCED d.h.w. temperature

40 (8…80)

°C

6.2 Setpoint

The NORMAL and REDUCED d.h.w. temperature setpoints are to be entered in °C.
When using thermostats, it must be made certain that the NORMAL setpoint entered
here agrees with the setpoint of the thermostat or – if 2 thermostats are used – of both
thermostats. If there is a deviation, the charging temperature cannot be correctly calcu-
lated (charging temperature = NORMAL setpoint [operating line 26] + boost of charging
temperature [operating line 127]).
If d.h.w. heating is switched to the electric immersion heater, the setpoint adjustment is
inactive in that case, since the thermostat of the electric immersion heater will ensure
temperature control of the storage tank.

6.3 Actual

value

The d.h.w. temperature is displayed in °C as follows, depending on the type of plant:

Plant type

Display

x–1, x–2, x–3

B31 or maximum selection of the 2 storage tank sensors B31 and B32

x–4

D.h.w. flow temperature sensor B3

If the measurement is made with one or 2 thermostats, it is not possible to display the
actual value. In that case, the display shows ---.

«
...
29
30
31
32
33
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Unico Страницы: 164

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: HEIDENHAIN Страницы: 257

Бренд: EFI Страницы: 127

Бренд: maxxess Страницы: 11

Бренд: SOLARJACK Страницы: 14

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

Бренд: HANYOUNG NUX Страницы: 4

Бренд: Jung Страницы: 8

AUTOMATIONWORX IBS PCI SC/I-T

Бренд: Phoenix Contact Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды