Siemens RVL481 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 118

background image

54/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

12 Function block "Boiler"

20.05.2008

12.4.4 Protective boiler startup

If the boiler temperature falls below the minimum limit of the boiler temperature while
the burner is running, the differential (minimum limit value minus actual value) will be
integrated. From this, a critical locking signal will be generated and transmitted to the
connected loads. This causes the loads to reduce their setpoints, thus consuming less
energy. If the critical locking signal exceeds a defined value, the boiler pump will be
deactivated also.
If the boiler temperature returns to a level above the minimum limit, the integral will be
reduced, resulting in a reduction of the critical locking signal. If the integral falls below a
defined level, the circulating pump will be activated again if it had been switched off.
The connected loads rise their setpoint values.
When the integral reaches the value of zero, protective boiler startup will be deacti-
vated, in which case the critical locking signal is zero.
Protective boiler startup can be interrupted to ensure that, in the event of a burner fault,
for instance, frost protection for the plant will be provided.
In the case of protective boiler startup and simultaneous frost protection for the plant,
the boiler temperature gradient must turn positive within 15 minutes. Otherwise, the
locking signal will become invalid for at least 15 minutes. On completion of the 15 min-
utes, protective boiler startup will become active again as soon as the boiler tempera-
ture gradient turns positive.
If the boiler carries out protective boiler startup, the boiler temperature controller's dis-
play shows

.

Protective boiler startup cannot be deactivated.
Section “25.4.7 Gain of locking signal” provides information on who receives the boiler
temperature controller's critical locking signal and how the consumers respond to it.

Controller 1
Plant type 2-1

Controller 1
Plant type 5-0

Controller 2

Controller 1 generates a critical locking
signal which deactivates the heating circuit
pump and the d.h.w. charging pump

Critical locking signal

LPB

Individual unit:

Interconnected plant:

252

4B

02e

Controller 1 switches
boiler pump off

Critical locking signal

Controller 3

«
...
52
53
54
55
56
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: Desoutter Страницы: 74

Бренд: HEIDENHAIN Страницы: 257

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: Olsen Страницы: 4

VLTAutomationDrive FC 360

Бренд: Danfoss Страницы: 52

Бренд: Nibe Страницы: 20

Бренд: maxon motor Страницы: 44

Бренд: M-Elec Страницы: 2

ACTPRO PRODUCT RANGE

Бренд: ACT Страницы: 8

Бренд: C-TEC Страницы: 42

Бренд: Broan Страницы: 2

Бренд: ECO POWER Страницы: 2

Бренд: Samson Страницы: 22

Бренд: Kilews Страницы: 26

Бренд: WOBIT Страницы: 25

Бренд: BZ PRODUCTS Страницы: 3

Бренд: Kicker Страницы: 2

exta life ROB-21

Бренд: Zamel Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды