Siemens RVL481 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 118

background image

27/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

4 Acquisition of measured values

20.05.2008

4.4.2 Handling

faults

If there is a short-circuit or open-circuit in the measuring circuit, and if the controller
requires the return temperature, it responds as follows:

•

If there is a return temperature from a controller of the same segment available on the

data bus, it is used (only with plant type 1–x). No error message will be generated
since this is the normal state in interconnected plants

•

However, if there is no return temperature available on the data bus, the return tem-

perature limitation functions will be deactivated and an error message generated

4.5

Secondary return temperature (B71)

4.5.1 Measurement

The secondary return temperature is acquired with a sensor having a sensing element
LG-Ni 1000. This measured value is required for DRT limitation (plant types 3–x and
6–x), together with the primary return temperature.

4.5.2 Handling

faults

If there is a short-circuit or open-circuit in the measuring circuit, and if the controller
requires the return temperature, DRT limitation will be deactivated. An error message
will be generated

4.6

D.h.w. flow temperature (B3)

4.6.1 Measurement

The d.h.w. flow temperature is acquired with a sensor having a sensing element
LG-Ni 1000.

4.6.2 Handling

faults

If there is a short-circuit or open-circuit in the measuring circuit, the d.h.w. will no longer
be heated. The charging pump is deactivated and the actuating device (slipper or seat
valve) is shut.
An error message will be generated.

4.7

D.h.w. storage tank temperature (B31, B32)

4.7.1 Measurement

The storage tank temperature can be acquired as follows:

•

With one or 2 sensors having a sensing element LG-Ni 1000, or

•

With one or 2 thermostats

This means that there are 2 measuring circuits.

«
...
25
26
27
28
29
...
»

Содержание RVL481























































































































Отзывы:

Нет отзывов

Похожие инструкции для RVL481

Бренд: NCR Страницы: 6

Бренд: Faber Страницы: 8

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: Vega Страницы: 20

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: Atari Страницы: 3

NovoCon S Digital

Бренд: Danfoss Страницы: 2

Dual Motor Focus Controller

Бренд: Pegasus Astro Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды