Siemens RVL481 Скачать руководство пользователя страница 23

Страница: 23 / 118

23/118

Siemens

Heating and D.h.w. Controller RVL481

CE1P2541en

Building Technologies

3 Fundamentals

20.05.2008

3.6 Manual

operation

The RVL481 can be switched to manual operation. In this case, the control will be
switched off. In manual operation, the various actuating devices behave as follows:

•

Heating circuit mixing valve: This mixing valve is not under voltage, but can be manu-

ally driven to any position by pressing the manual buttons

/ (close) and

/ (open). The heating circuit pump / circulating pump is continuously running.

•

Boiler: The 2 burner stages are continuously on. The manual button

/ can be used

to switch the second stage on and off. Pump M1 is continuously running

•

Charging pump: The charging pump is continuously running

•

Collector pump: The collector pump is continuously running

•

Changeover valve: The changeover

valve is always in the ”Heating circuit” position

•

D.h.w. slipper / seat valve: This valve is driven to the fully closed position, in which

case the closing time is five times the set running time. Then, it is deactivated

•

Circulating pump M4: Continuously running

•

Electric immersion heater K6: Continuously released

•

Multifunctional relay: Continuously energized

Manual operation also negates any overriding of the controller's operating mode (bridg-
ing of H1–M).

3.7

Plant type and operating mode

Depending on the selected type of plant, the following operating modes are available:

Plant type

1–0 YES

YES

YES YES NO YES

1–1, 1–2, 1–4, 1–5

YES

YES YES YES YES YES

2–0 YES

YES

YES YES NO YES

2–1, 2–2, 2–3, 2–5

YES

YES YES YES YES YES

3–0 YES

YES

YES NO YES

3–1, 3–2, 3–3, 3–4, 3–5

YES YES YES YES YES YES

4–0

YES

4–1, 4–2, 4–5

YES

5–0

YES

5–1, 5–2, 5–4, 5–5

YES

6–0

YES

6–1, 6–2, 6–5

YES

* Depending on the boiler's operating mode:

– Boiler with automatic shutdown: NO
– Boiler with manual shutdown: YES

Содержание RVL481























































































































Результаты поиска

Содержание RVL481

Отзывы:

Похожие инструкции для RVL481

Бренды по названию

Популярные бренды

Siemens RVL481, Основная документация

Результаты поиска

Содержание RVL481

Отзывы:

Похожие инструкции для RVL481

Бренды по названию

Популярные бренды