manualshive.com logo in svg

Siemens interranger DPS300, Инструкция пользователя, Страница: 68 / 111

Поделиться
Скачать
Siemens interranger DPS300 Скачать руководство пользователя страница 68

InterRanger DPS300 

68

 7ML19981BC01

 

 ENHANCEMENT PARAMETERS  

This section identifies all DPS300 operator programmable features designed for 
altering operation to suit individual operator preferences or overcome 
measurement difficulties.  

Typically, these parameters are only altered as directed by the 
TROUBLESHOOTING GUIDE. If RUN mode performance requires improvement, 
access and alter the following parameters as required.  

Note: 

Otherwise, proceed to OPERATION. 

PARAMETER CATEGORY 

PURPOSE 

PAGE

Data Logging 

to view previous maximum Temperature records 

68 

Profile Records 

intended for use by Siemens Service Personnel 

69 

Installation Records 

to identify length of service and power failure occurrence 

72 

Range Calibration 

to compensate for measurement offset and/or sound velocity 

72

Temperature Compensation 

to override automatic temperature compensation features 

74 

Rate 

to adjust the rate of response to change in the sludge level 

75 

Measurement Verification 

to adjust the rate of response to change in the sludge level 

77 

Display Parameters 

to override the preset display operating characteristics 

78 

Echo Processing 

to troubleshoot false echo detection 

81 

Advanced Echo Processing 

intended for use by Siemens Service personnel 

83 

Test Parameters 

intended for use by Siemens Service personnel 

90 

Measurement Parameters 

to verify Application Parameter programming 

92 

Master Reset 

to reset Parameter Values to factory settings 

93 

Note: 

When an Enhancement Parameter is altered, return to the RUN mode to verify the 
performance desired is achieved, before making any other changes.  

Data Logging Parameters (P300 and P302)  

View the maximum Temperature recorded in the RUN mode.  

P300  (V)  Temperature, Transducer Max  

Use this feature to view the highest temperature recorded (in ° C) by the XCT-12 
transducer. 

Values: 

-50 to 150  

P302  (V)  Temperature, Sensor Max  

Use this feature to view the highest temperature recorded (in ° C) by the TS-3 
temperature sensor, if used. 

When accessed, the TS-3 symbol is displayed in the Point Type field and the TS-3 
Number is displayed in the Point Number field.  

Values: 

-50 to 150

  

Содержание interranger DPS300
















































































































Отзывы:

Нет отзывов