Siemens interranger DPS300 Скачать руководство пользователя страница 43

Страница: 43 / 111

7ML19981BC01

InterRanger

DPS300

Keypad – Program Mode

In the program mode, use the DPS300 programmer keys to perform the identified
functions.

shift access to Point Number, Parameter Number, or Parameter Value

display.

—

input the numeric value into the accessed display.

input a Parameter Value decimal point (moves Profile and TVT Pointers

left).

input a negative Parameter Value (moves Profile and TVT Pointers right).

delete the current Parameter Value display (initiate a parameter reset).

store the current Parameter Value in memory (complete a parameter

reset).

switch the Parameter Value to % or Units (access Auxiliary Parameter

Function).

increase the accessed display value.

decrease the accessed display value.

take an ultrasonic measurement.

enter the RUN mode.

numeric value keys

function keys

Содержание interranger DPS300
















































































































Результаты поиска

Содержание interranger DPS300

Отзывы:

Siemens interranger DPS300, Инструкция пользователя, Страница: 43 / 111

Результаты поиска

Содержание interranger DPS300

Отзывы: