manualshive.com logo in svg

Siemens interranger DPS300, Инструкция пользователя, Страница: 65 / 111

Поделиться
Скачать
Siemens interranger DPS300 Скачать руководство пользователя страница 65

 

7ML19981BC01 

65

 InterRanger 

DPS300

 

P202  mA Allocation  

Use this feature if Point Number to mA output allocation alteration is required.  
Enter the Point Number(s) the mA output displayed, is to be based upon.  

As preset, mA outputs 1 and 2 are allocated to Point Numbers 1 and 2 
respectively.  

If Point 1 and 2 are allocated to a single mA output, the output value represents 
the Dual Point Average. (The Quick Start Parameter values should be identical for 
both points). 

When both mA outputs are allocated to the same Point Number, the mA Setpoint 
parameters may be used to establish two separate or overlapping mA output 
spans. However, the mA Value / Transducer (P203) corresponds to mA Output 1 
only.  

Values

: 

1 = Point 1  
2 = Point 2  

 

1.2  = Dual Point Average  

P203 (V)  mA Value / Transducer  

View the current value of the mA output associated with the Point Number 
displayed.  

This is the Auxiliary Reading displayed when [mA] is pressed in the RUN mode.  

If both mA outputs are allocated to the same Point Number, the value of mA 
Output 1 is displayed.  

Values: 

0.000 to 22.00 

 

P210  0/4 mA Setpoint  

Use this feature to reference the minimum mA output to any point in the 
measurement range.  

Enter the material level (referenced to Empty, P006) corresponding to the 
minimum mA output.  

This feature is preset to 0% or 100% of Span (P007) as determined by Operation 
(P001).  

Typically, this value is entered in Units (P005) or percent of Span (P007). If mA 
Function is set for “volume”, enter the value in the Max Volume (P051) units or in 
percent of Max Volume.  

Values:  

-999 to 9999

  

P211  20 mA Setpoint  

Use this feature to reference the 20 mA output to any point in the measurement 
range.  

Enter the sludge level (referenced to Empty, P006) corresponding to 20 mA.  

Содержание interranger DPS300
















































































































Отзывы:

Нет отзывов